搜索
NEWS
NEWS
Position:
Home
-
-
-
Installation of air lubricator

Installation of air lubricator

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2020-09-01
  • Views:0

(Summary description)During installation, the air lubricator should generally be installed after the water separator and the pressure reducing valve, and before the reversing valve, enter the oil cup with the water separator to emulsify the oil, so as to prevent the overflow hole in the pressure reducing valve from being polluted by oil mist and The rubber parts are affected by oil mist. The air oil mister should be as close as possible to the lubrication part. The distance of ordinary air oil mister is generally not more than 5m, and the conveying distance of micro-mist air oil mister can reach 8~10m.

Installation of air lubricator

(Summary description)During installation, the air lubricator should generally be installed after the water separator and the pressure reducing valve, and before the reversing valve, enter the oil cup with the water separator to emulsify the oil, so as to prevent the overflow hole in the pressure reducing valve from being polluted by oil mist and The rubber parts are affected by oil mist. The air oil mister should be as close as possible to the lubrication part. The distance of ordinary air oil mister is generally not more than 5m, and the conveying distance of micro-mist air oil mister can reach 8~10m.

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2020-09-01
  • Views:0
Information

During installation, the air lubricator should generally be installed after the water separator and the pressure reducing valve, and before the reversing valve, enter the oil cup with the water separator to emulsify the oil, so as to prevent the overflow hole in the pressure reducing valve from being polluted by oil mist and The rubber parts are affected by oil mist. The air oil mister should be as close as possible to the lubrication part. The distance of ordinary air oil mister is generally not more than 5m, and the conveying distance of micro-mist air oil mister can reach 8~10m.

During installation, the inlet and outlet should not be reversed, install vertically and as high as possible higher than the lubrication part, and should be installed as high as possible than the lubrication part. Pay attention to maintaining the normal oil level, and should not be too high or too low. The synthetic rubber should be selected. The viscosity of the clean lubricant that has little effect on the deformation, hardening and softening of the sealing material should not be too large or too small. It is recommended to use ISOVG32, that is, the viscosity of the oil is about 32mm2/s, so as to avoid difficulty in oil absorption or excessive oil consumption. The amount of oil dripping should be adjusted according to the conditions of use, generally based on 10m3 (ANR) air supply and 1cm3 lubricating oil.

The material of the oil cup, inspection cover and oil drop tube is PC, which cannot be used in the environment of organic solvents, and should be protected from direct sunlight.

There is no air lubricator for parts that do not need to be supplied with oil. In order to prevent air backflow during shutdown and cause oil mist to be mixed into the circuit that does not need to be supplied with oil, a one-way valve can be installed in front of the air lubricator.

The air lubricator can also be used for refueling when it is working. When refueling, the input oil and compressed air close the air check valve, thereby cutting off the gas and the upper cavity channel. Gas cannot enter the upper cavity, and the oil check valve is closed due to the lower pressure in the upper cavity, and the gas will not enter the upper cavity from the oil suction pipe, so the air can be supplied to the lubricator from the oil plug port without stopping the gas supply. come on.

Scan the QR code to read on your phone

Recommended news

Support Hotline

Address: No. 54 Dalian Road, High-tech Industrial Development Zone, Weihai City, Shandong Province

ZHPC

ZHPC

Website QR Code

Copyright © Weihai Zhonghao Pneumatic Hydraulic Co., Ltd. Powered by www.300.cn   鲁ICP备15004029号   This site supports IPV6 access